Access the Temperature Control Dial: Open the refrigerator door and reach for the temperature control dial.It is marked with numbers or labeled as “Freezer Temperature Control.” Locate the Temperature Control Dial: The temperature control dial is typically located inside the refrigerator compartment, either on the upper back wall or on the ceiling.Setting the freezer temperature on your Whirlpool refrigerator is a simple process. Close the filter cover door completely in order.How Do You Set Freezer Temperature on Whirlpool Refrigerator?.The filter cover door will automatically begin to close as the new filter is inserted. With the arrow pointing up, align the new filter with the filter housing and slide it into place.Be sure the O-rings are still in place after the cap is removed.Take the new filter out of its packaging and remove the cap.NOTE: There may be some water in the filter. When the door is completely open, pull the filter straight out.The filter will be released and then be ejected as the door is opened. Locate the water filter in the top-right corner of the refrigerator compartment.To manually turn off the ice maker, flip the switch to the OFF (down) position.To turn on the ice maker, flip the switch to the ON (up) position.The On/Off switch, located on the left wall of the freezer door, can only be accessed when the ice storage bin has been removed.When cooling is off, “COOLING OFF” will appear on the display screen. ![]() IMPORTANT: To avoid unintentionally locking the dispenser or changing other settings, be sure to press both buttons at exactly the same time.To turn cooling off, press and hold the LOCK and MEASURED FILL buttons at the same time for 3 seconds.Your refrigerator and freezer will not cool when cooling is turned off.NOTE: To exit without saving changes, press ICE TYPE at any time while in adjust mode, or allow about 60 seconds of inactivity and adjust mode will turn off automatically. When you have finished viewing (and adjusting if desired) both the refrigerator and freezer set points, press MEASURED FILL to save the settings.“FREEZER” appears on the display screen.When you have finished viewing (and adjusting if desired) the refrigerator set point, press TMP to change the display to show the freezer set point. Press LOCK to raise the set point, or press OPTIONS to lower the set point.When adjust mode is activated, the display screen shows the refrigerator set point and “FRIDGE” appears. To return the display setting to Fahrenheit, press LIGHT again. ![]() NOTE: To view Celsius temperatures, press the LIGHT button when adjust mode is activated. SERVICE MANUAL – Whirlpool Gold Series Refrigerator Service PDF Manual Whirlpool Gold Series Refrigerator Use Guide Whirlpool Gold Series Refrigerator Troubleshooting When adjust mode is activated, adjusting information will appear on the display screen. To view and adjust the set points, press and hold the TEMP button for 3 seconds. Recheck the temperatures before other adjustments are made. Wait at least 24 hours between adjustments. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm. The preset settings should be correct for normal household usage. If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls. NOTE: Adjusting the set points to a colder than recommended setting will not cool the compartments any faster. If you add food before the refrigerator has cooled completely, your food may spoil. Wait 24 hours before you put food into the refrigerator. When you first install your refrigerator, make sure that the controls are still set to the “mid-settings.” The factory recommended set points are 37☏ (3☌) for the refrigerator and 0☏ (-18☌) for the freezer. Adjusting Refrigerator Freezer Temperatureįor your convenience, your refrigerator and freezer controls are preset at the factory. While in “sleep” mode, the first press of a control button will only reactivate the display screen without changing any settings. IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser pads have not been used for 2 minutes or more. The refrigerator and freezer controls are located on the dispenser panel. Whirlpool Gold Refrigerator Temperature Control Panel Quick Fix Using the Main Panel Controls ![]() This includes Ice maker issues, water filter problems, and water leaking and water problems. We have the refrigerator use guide and a list for troubleshooting your Whirlpool Gold Refrigerator. When your Whirlpool Gold Series Refrigerator is not working properly, the user manual will assist you in finding and fixing the problem.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |